Dental Casting Resin PioNext Cherry Red
Dental Casting Resin PioNext Cherry Red is a UV curable resin for 3D printing dental casting models. The material is intended for cast crowns, denture framework structures, and other dental and medical casting applications. The resin combines low shrinkage, high hardness, low ash residue, good fluidity, and high printing accuracy.
Features and Benefits
- Cherry Red color
- Low ash residue
- Low shrinkage
- High surface hardness
- High molding accuracy
- Fast burning
- Smooth model surface
- Good material fluidity
- Suitable for precise dental casting
- Compatible with LCD and DLP printers
Applications
- Cast dental crowns
- Denture framework structures
- Removable framework parts
- Dental casting models
- Small batch dental production
- Other dental and medical casting applications
Compatibility and Colors
The material is compatible with LCD and DLP equipment. The manufacturer presentation shows Cherry Red and Green color options. This page is prepared for the Cherry Red version.
Technical Specifications
| Parameter | Value |
|---|---|
| Color | Cherry Red |
| Viscosity at 25 C | 100 - 200 cps |
| Density at 25 C | 1.05 - 1.10 g/cm3 |
| Hardness | 80 - 85 Shore D |
| Flexural Modulus | 1500 - 2000 MPa |
| Flexural Strength | 45 - 65 MPa |
| Tensile Modulus | 600 - 1000 MPa |
| Tensile Strength | 35 - 55 MPa |
| Elongation at Break | 10 - 15 % |
| Impact Strength Notched Izod | 60 - 80 J/m |
| Heat Deflection Temperature | 70 - 80 C |
| Bakeout Temperature | 850 C, 1.5 h |
Additional Data from the Manufacturer Presentation
| Parameter | Claimed Value |
|---|---|
| Hardness | More than D80 |
| Flexural modulus | More than 1500 MPa |
| Sintering temperature | 850 - 900 C |
| Sintering time | 1 - 1.5 h |
| Casting wall thickness | More than 0.35 mm |
| Printed product storage time | Less than 10 h |
| Ash value | Less than 0.05 % |
Recommended Starting Print Parameters for Anycubic
| Printer | Layer Thickness | Base Layer Exposure | Normal Layer Exposure | Lift Speed |
|---|---|---|---|---|
| Anycubic Photon Mono M5s | 0.05 mm | 70 s | 4.5 s | 5 mm/s |
| Anycubic M7 Pro | 0.05 mm | 70 s | 3.2 s | 7 mm/s |
| Anycubic DLP D2 | 0.05 mm | 40 s | 5.6 s | 5 mm/s |
General Print Parameters
| Equipment Type | Layer Thickness | Base Layer Exposure | Normal Layer Exposure | Lift Speed |
|---|---|---|---|---|
| LCD | 0.05 - 0.1 mm | 45 - 50 s | 4.0 - 4.5 s | 3 - 4 mm/s |
| DLP | 0.05 - 0.1 mm | 25 - 30 s | 3.0 - 3.3 s | 3 - 4 mm/s |
UV Post Processing Recommendations
| Device | Wavelength | Light Intensity | Recommended Time | Curing in Water or Without |
|---|---|---|---|---|
| UV02 | 405 nm | 30 % | 5 min recommended, 4 - 8 min range | Without water |
These values are starting points only. Final settings should be adjusted according to the printer model, resin temperature, room conditions, model geometry, and casting process requirements.
Advantages of Digital Dental Applications
- High precision reproduction of model geometry
- Delicate surface texture
- Reduced production time
- More cost effective casting workflow
- Suitable for digital dental workflows
Post Processing
- Clean the model with absolute ethanol or isopropanol using low frequency ultrasonic cleaning.
- Do not use high frequency cleaning and do not scrub the model to avoid damaging the surface.
- Remove residual liquid from the surface using air or a hair dryer.
- It is recommended to remove the main supports before final post curing and remove fine support marks after curing.
- Additional curing time should be adjusted according to the selected post curing mode.
Storage
Store below 25 C in a place protected from light. Do not leave the material under sunlight, in a humid environment, or near corrosive substances. Shelf life is 18 months.
Safety Information
- This material is for one time use and cannot be reused.
- Ensure good ventilation and proper protective measures during use.
- If the material gets into the eyes, rinse immediately with plenty of clean water and seek medical attention.
- If the material contacts skin, remove contaminated clothing and wash the area thoroughly with soap and water.
- The material is not intended for contact with food or drink.
- Refer to the manufacturer MSDS for additional information.