Castable White Wax Resin PioNext PN-JC20 20 Percent Wax Content
Castable White Wax Resin PioNext PN-JC20 is a UV curable resin for 3D printing castable jewelry models with 20 percent wax content. The material is designed for precise jewelry casting and is suitable for rings, pendants, earrings, and other complex items with fine details. This resin provides high accuracy, smooth surfaces, low shrinkage, and clean burnout with minimal ash residue.
Features and Benefits
- 20 percent wax content
- High printing accuracy
- Low shrinkage
- Clean burnout and low ash residue
- Smooth model surface
- Suitable for complex and fine jewelry details
- Good material fluidity
- Suitable for serial jewelry production
- Low skin irritation and low skin allergenic characteristics according to the manufacturer
Applications
- Rings
- Earrings
- Pendants
- Jewelry master models
- Castable models for serial production
- Jewelry prototyping
Suitable for Metal Casting
This resin is suitable for standard vacuum investment casting and can be used for casting items in gold, silver, copper, 18K alloys, and other metals.
Technical Specifications
| Parameter | Value |
|---|---|
| Model | PN-JC20 |
| Wax Content | 20 percent |
| Viscosity at 25 C | 50 - 150 cps |
| Density at 25 C | 1.05 - 1.15 g/cm3 |
| Ash Content | Less than 0.1 percent |
| Net Weight | 500 g, 1000 g |
Recommended Burnout Cycle
| Stage | Temperature | Time |
|---|---|---|
| Stage 1 | 180 C | 3 hours |
| Stage 2 | 350 C | 2.5 hours |
| Stage 3 | 600 C | 3 hours |
Recommended Starting Print Parameters
| Printer | Layer Thickness | Base Layer Exposure | Normal Layer Exposure | Lift Speed |
|---|---|---|---|---|
| DJ-89 | 0.05 - 0.1 mm | 30 - 60 s | 6.5 - 7.5 s | 1 - 8 mm/s |
| DJ-89Plus | 0.05 - 0.1 mm | 30 - 60 s | 6.5 - 7.5 s | 1 - 10 mm/s |
| D128 | 0.05 - 0.1 mm | 30 - 60 s | 6.5 - 7.5 s | 1 - 3 mm/s |
| D136 | 0.05 - 0.1 mm | 30 - 60 s | 6.5 - 7.5 s | 1 - 5 mm/s |
| D158 | 0.05 - 0.1 mm | 20 - 40 s | 3.5 - 4.5 s | 1 - 10 mm/s |
| C01 | 0.05 - 0.1 mm | 30 - 60 s | 6.5 - 7.5 s | 1 - 10 mm/s |
| C02 | 0.05 - 0.1 mm | 30 - 60 s | 6.0 - 7.0 s | 1 - 10 mm/s |
| Halot One | 0.05 - 0.1 mm | 30 - 60 s | 8.5 - 9.8 s | 1 - 3 mm/s |
| Halot Sky | 0.05 - 0.1 mm | 30 - 60 s | 6.5 - 7.5 s | 1 - 8 mm/s |
| Halot Mage | 0.05 - 0.1 mm | 30 - 60 s | 3.5 - 4.5 s | 1 - 3 mm/s |
| Anycubic Photon Mono M5s | 0.05 - 0.1 mm | 30 - 60 s | 6.5 - 7.5 s | 1 - 20 mm/s |
| Elegoo Saturn 3 Ultra | 0.05 - 0.1 mm | 30 - 60 s | 6.5 - 7.5 s | 1 - 10 mm/s |
These values are starting points only. Final settings should be adjusted according to the printer model, resin temperature, room conditions, model geometry, and support strategy.
Digital Jewelry Process
- 3D model printing
- Model processing
- Wax tree assembly
- Gypsum injection
- Vacuum process
- High temperature dewaxing
- Casting
- Taking out and polishing
Post Processing
- Clean the printed model with absolute ethanol or isopropanol.
- Low frequency ultrasonic cleaning can be used.
- High frequency or high power ultrasonic cleaning is not recommended because it may damage the model surface.
- After cleaning, remove all remaining liquid with air or a hair dryer.
- The main supports should be removed before final post curing.
- If needed, additional UV curing for about 5 minutes can be applied.
Storage
Store below 25 C in a place protected from light. The material is sensitive to visible light. Shelf life under proper storage conditions is up to 18 months.
Safety Information
- Avoid contact with eyes and skin.
- If the resin gets into the eyes, rinse immediately with plenty of clean water and seek medical attention.
- If the resin contacts skin, remove contaminated clothing and wash the area thoroughly with soap and water.
- This material is not intended for contact with food or drink.
- Refer to the manufacturer MSDS for additional information.