Anycubic Offset Measurement Module for Kobra 2 Series
SKU: S010118
Manufacturer: Anycubic
Compatibility: Anycubic Kobra 2, Kobra 2 Neo, Kobra 2 Pro, Kobra 2 Plus, Kobra 2 Max
Purpose: offset measurement module for printer calibration
Description
The Anycubic Offset Measurement Module is a replacement electro-mechanical spare part for Anycubic Kobra 2 Series FDM 3D printers. The module is used in the calibration system and helps the printer perform offset-related measurements required for stable first-layer setup.
A properly functioning module is important for accurate calibration procedures, correct nozzle positioning relative to the build surface and predictable print start. If the module is damaged, disconnected or unstable, the printer may produce calibration errors, an incorrect first layer, or an excessive or insufficient gap between the nozzle and the build plate.
Key Benefits
- Original Anycubic spare part for the Kobra 2 Series.
- Compatible with Kobra 2, Kobra 2 Neo, Kobra 2 Pro, Kobra 2 Plus and Kobra 2 Max.
- Used in the offset measurement and calibration system.
- Helps maintain stable first-layer performance.
- Suitable for repair, maintenance and restoring normal printer operation.
- Installed in the heated bed area according to the printer design.
Technical Specifications
| Product name | Anycubic Offset Measurement Module |
| Alternative name | Offset Measurement Switch Module |
| SKU | S010118 |
| Manufacturer | Anycubic |
| Part type | Measurement module / calibration module |
| Installation area | Heated bed area / calibration assembly |
| Compatible models | Anycubic Kobra 2, Kobra 2 Neo, Kobra 2 Pro, Kobra 2 Plus, Kobra 2 Max |
| Category | Spare parts for Anycubic FDM 3D printers |
When Replacement May Be Needed
- The printer does not complete the calibration procedure correctly.
- After auto-calibration, the first layer is too compressed or too high.
- The module is physically damaged, cracked or has damaged wiring.
- Offset measurement operation is affected after transportation or repair.
- Errors related to offset measurement or calibration appear.
- The Kobra 2 Series calibration system needs to be restored to normal operation.
Installation Recommendations
- Turn off the 3D printer and disconnect the power cable before maintenance.
- Remove the PEI sheet from the heated bed.
- Locate the module mounting position in the heated bed area.
- Carefully disconnect the old module from the wiring.
- Connect the new Offset Measurement Module to the original connector.
- Align the module holes with the mounting holes and secure it with screws.
- Place the PEI sheet back on the build platform.
- After replacement, run printer calibration and check first-layer quality.
Compatibility
The Offset Measurement Module with SKU S010118 is compatible with Anycubic Kobra 2, Kobra 2 Neo, Kobra 2 Pro, Kobra 2 Plus and Kobra 2 Max. For other Anycubic models, compatibility should be checked separately according to the correct SKU and calibration assembly design.
FAQ
Which printers is this module compatible with?
The module is compatible with Anycubic Kobra 2, Kobra 2 Neo, Kobra 2 Pro, Kobra 2 Plus and Kobra 2 Max.
What is the SKU?
The SKU is S010118.
What is the Offset Measurement Module used for?
It is used in the offset measurement and calibration system to help the printer set the correct position for a stable first layer.
Do I need to calibrate the printer after replacement?
Yes. After replacing the module, run printer calibration and check first-layer quality.
Is it compatible with Kobra 2 Neo?
Yes, SKU S010118 is listed as compatible with Anycubic Kobra 2 Neo.