Model Cooling Fan for Anycubic Kobra 3 / Kobra 3 Combo
SKU: S010229
Manufacturer: Anycubic
Compatibility: Anycubic Kobra 3, Anycubic Kobra 3 Combo
Purpose: model cooling fan / part cooling fan for printed layer cooling
Description
The Model Cooling Fan for Anycubic Kobra 3 and Kobra 3 Combo is a replacement spare part for the print head of an FDM 3D printer. It provides directed airflow to the freshly printed layer, helping stabilize melted filament after it leaves the nozzle and improving overhangs, bridges, small details and surface quality.
A properly working model cooling fan is especially important when printing PLA, PLA+, PETG, TPU and other materials where airflow affects detail quality, corner sharpness, bridge performance and heat control on thin sections. If the fan is weak or not working, prints may show blobs, sagging, overheated edges, poor bridging and less accurate surface finish.
Key Benefits
- Original Anycubic spare part for Kobra 3 and Kobra 3 Combo.
- Used to cool the printed layer and material exit zone.
- Helps improve bridge, overhang and fine-detail quality.
- Supports consistent print quality at higher speeds.
- Suitable for replacing a worn, noisy, damaged or contaminated fan.
- An important part for reliable PLA, PETG, TPU and other FDM filament printing.
Technical Specifications
| Product name | Model Cooling Fan for Anycubic Kobra 3 / Kobra 3 Combo |
| Original name | Model Cooling Fan for Anycubic Kobra 3 | Anycubic Kobra 3 Combo |
| Alternative name | Material Cooling Fan |
| SKU | S010229 |
| Manufacturer | Anycubic |
| Part type | Model cooling fan / part cooling fan |
| Fan size | 50 × 50 × 20 mm |
| Voltage | 24 V |
| Speed | 7000 rpm |
| Installation area | Print head / model cooling system |
| Compatible models | Anycubic Kobra 3, Anycubic Kobra 3 Combo |
| Category | Spare parts for Anycubic FDM 3D printers |
When Replacement May Be Needed
- The fan does not spin or starts inconsistently.
- Strong noise, grinding, vibration or impeller wobble appears.
- Model cooling becomes weaker because of wear, dust or fan damage.
- Bridge, overhang and fine-detail quality becomes worse.
- Thin sections overheat, causing blobs, sagging or soft edges.
- The fan works intermittently after print head maintenance.
- The Kobra 3 / Kobra 3 Combo print head cooling system is being repaired.
Installation Recommendations
- Turn off the 3D printer and disconnect the power cable before maintenance.
- Wait until the hotend, nozzle and working area cool down completely.
- Remove the print head cover if needed to access the fan.
- Take a photo of the old fan cable and connector position before removal.
- Carefully disconnect the old Model Cooling Fan without pulling on the wires.
- Install the new fan in the original position and secure it with the mounting screws.
- Connect the cable and make sure it does not touch the impeller or moving parts.
- After installation, check fan startup, airflow direction and run a test print.
Compatibility
The Model Cooling Fan with SKU S010229 is intended for Anycubic Kobra 3 and Anycubic Kobra 3 Combo. For Kobra Go, Kobra Neo, Kobra 2, Kobra 2 Neo, Kobra 2 Pro, Kobra 2 Plus, Kobra 2 Max, Kobra S1 and other models, compatibility should be checked separately by SKU, fan size, connector and print head design.
FAQ
Which printers is this fan compatible with?
This fan is intended for Anycubic Kobra 3 and Anycubic Kobra 3 Combo.
What is the SKU?
The SKU is S010229.
What is a Model Cooling Fan?
It is a part cooling fan that cools the freshly printed layer after material leaves the nozzle.
Is this a hotend cooling fan or model cooling fan?
This is a model cooling fan / part cooling fan. It is not the main heatsink fan for hotend cooling.
What are the fan specifications?
The fan size is 50 × 50 × 20 mm, voltage is 24 V, and speed is about 7000 rpm.
When should the model cooling fan be replaced?
Replacement is recommended when the fan stops, becomes noisy, vibrates, airflow becomes weak or bridge and overhang quality becomes worse.