LCD Screen for Anycubic Photon Mono X 6Ks
Description
LCD Screen for Anycubic Photon Mono X 6Ks is a replacement monochrome screen for the Anycubic Photon Mono X 6Ks resin 3D printer. The screen is used in the layer exposure system and forms the image of each layer during printing.
The LCD screen is one of the key parts of a resin 3D printer. Print detail, contour sharpness, exposure stability, even resin curing and final model quality depend on its condition. A new screen helps restore print accuracy after damage, wear or exposure defects.
Screen replacement may be required if printed models show lines, spots, dead zones, cracks, uneven exposure, layer defects or if resin has leaked onto the screen. A properly working screen is especially important for miniatures, prototypes, master models, decorative parts and functional components.
Advantages
- Compatible with Anycubic Photon Mono X 6Ks
- Replacement part for a resin 3D printer
- Monochrome LCD screen for layer exposure of resin
- 6K 5760 x 3600 px resolution for high model detail
- 9.1″ screen diagonal
- 380:1 contrast ratio
- 6.5% light transmission
- Up to 2000 hours screen lifespan
- Helps restore print quality after screen damage
- Suitable for repair and service maintenance
Technical Specifications
| Product name | LCD Screen for Anycubic Photon Mono X 6Ks |
| Full product name | LCD screen for 3D printer Anycubic Photon Mono X 6Ks |
| SKU | S020143 |
| Part type | LCD screen, monochrome screen, exposure screen |
| Compatibility | Anycubic Photon Mono X 6Ks |
| Screen diagonal | 9.1″ |
| Resolution | 6K 5760 x 3600 px |
| Contrast ratio | 380:1 |
| Light transmission | 6.5% |
| Screen lifespan | Up to 2000 hours |
| Screen type | Monochrome LCD screen |
| Printer type | LCD resin 3D printer |
| Purpose | Layer image formation and UV exposure of photopolymer resin |
| Category | LCD screens for Anycubic resin 3D printers |
When to Replace the LCD Screen
- Printed models show lines, spots or repeated defects
- Part of the model does not print because of dead zones on the screen
- Resin exposure becomes uneven
- The screen has been damaged after resin leakage
- The screen has cracks, dark zones or mechanical damage
- The printer does not form a layer image during the exposure test
- Diagnostics confirm an LCD screen fault
- Print quality becomes worse with the same resin settings
Compatibility
This LCD screen is intended for Anycubic Photon Mono X 6Ks. Before ordering, check the printer model and part number S020143. Anycubic Photon Mono X, Photon Mono X 6K, Photon Mono X2, Photon M3 Plus, Photon Mono 4K, Photon Mono 2 and other models use different screens.
Important Difference
This product is intended specifically for Anycubic Photon Mono X 6Ks and has SKU S020143. It should not be confused with the screen for Anycubic Photon Mono X 6K or Photon M3 Plus, as these models may use other compatible parts. The printer model, product name and SKU should be checked before ordering.
Installation Recommendations
- Turn off the printer completely and disconnect the power cable before replacement
- Remove the resin vat and build platform
- Clean the working area from resin residue and dust
- Take a photo of ribbon cable and wire connections before disassembly
- Do not bend the screen ribbon cable or pull it with force
- Do not touch the screen surface with dirty or wet hands
- Run an exposure test after installation
- After replacement, check exposure uniformity across the whole screen area
- If you do not have electronics repair experience, contact a qualified technician
Usage Recommendations
- Always check the vat film condition before printing
- Do not allow resin to leak onto the LCD screen
- Use a screen protector to reduce damage risk
- Do not clean the screen with sharp tools
- After a failed print, check the vat bottom for cured resin residue
- Clean dust from the screen regularly with a soft wipe
- If print defects appear, run an exposure test before replacing other parts
- Use correct exposure settings for the selected photopolymer resin
Suitable Applications
- Repair of Anycubic Photon Mono X 6Ks
- Replacement of a damaged LCD screen
- Restoration of even photopolymer resin exposure
- Service maintenance of a resin 3D printer
- Solving layer defects, spots and dead zones
- Printing miniatures, prototypes, master models and functional parts
- Restoring stable 6K resin printing quality
FAQ
Is this LCD screen compatible with Anycubic Photon Mono X 6Ks
Yes, this LCD screen is intended for Anycubic Photon Mono X 6Ks.
What is the SKU of LCD screen for 3D printer Anycubic Photon Mono X 6Ks
The SKU of this part is S020143.
What is the screen diagonal of Photon Mono X 6Ks
Photon Mono X 6Ks uses a 9.1″ monochrome screen.
What is the screen resolution of Photon Mono X 6Ks
The screen resolution is 6K 5760 x 3600 px.
Is this screen compatible with Photon Mono X 6K
This screen is listed for Photon Mono X 6Ks. Photon Mono X 6K requires a separately compatible screen and SKU verification.
When should the LCD screen be replaced
The screen should be replaced if cracks, dead zones, lines, spots, uneven exposure, resin leakage damage or confirmed diagnostic faults appear.
Should I run an exposure test after screen replacement
Yes, after installing a new LCD screen, run an exposure test and a test print to check exposure uniformity and correct printer operation.